Payment & Shipping Terms:
|Type:||SMD LED||Chip Material:||InGaN|
|Emitting Color:||Red||Luminous Intensity:||Customers' Requirements|
|Viewing Angle(°):||120 Degree||Color Rendering Index:||Null|
|Color Temperature:||620-630nm||Operating Temperature:||-20 - 85|
|Chip Brand:||Epistar Chip, Sanan Chip,Epileds Chip||Current:||30mA|
1. High Lumens Output & Low Brightness Decay
2. Stable Performance & Great CCT Inity.
3. Wid Color Temperature Range
1. First-Choice for Indoor Ligting
2. Good raw materials
3. Copper layer
4. Gold wire connection
6. Lifespan is >50 000 hours easily
|SURFACE MOUNT LED LAMPS|
|Absolute maximum ratings (Ta=25°C)|
|Operating temperature range||Top||-25~+80||°C|
|Storage temperature range||Tstg||-30~+85||°C|
|Peak pulsing current(1/8 duty f=1KHz)||Ifp||50||mA|
|Electro-Optical characteristics (TA=25°C)|
Viewing angle at 50% IV
Color Rendering Index
Carrier Tape Dimensions:
Loaded quantity 4000 PCS Per reel.
Please read the following notes before using the product:
Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen).
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.
2.3 The LEDs should be used within a year.
2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less.
2.5 The LEDs should be used within 168 hours (7 days) after opening the package.
2.6 If the moisture adsorbent material (silica gel) has fabled away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment: 60±5℃ for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile.
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
4. Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 260℃ for 5 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder.
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.
Are widely used in the LED lamp, LED bulb light, LED panel light, LED ceiling lamp, LED street light, LED lamp, miner's lamp, stage light, flashlight, lighting, lamp lighting lamps and lanterns, as well as outdoor billboards, such as electronic display, traffic lights, signs, car tail lights, LED modules, LCD back light, LED lighting lighting, LED soft/hard light bar, etc., is the better choice to replace traditional lighting light source.
We provide EMS DHL UPS FedEx TNT that several different types of express allows you to select, under normal circumstances, the transport time is in 5 to 10 days or so, if large cargo, go shipping, so time is longer, but safer, and the freight is lower.
Q1. Can I have a sample order?
A: Yes, we welcome sample order to test and check quality. Mixed samples are acceptable .free samples will be available.
Q2: What’s the delivery time?
A: It usually takes about 5-7 days to produce an order. But the exact delivery time might be different for different orders or at different time.
Q3:What's your warranty terms?
A: The warranty for all our Led products is 2 years.
Q4: How does your factory do regarding quality control?
A: Quality is priority.We always believe Quality is our marketing and attach great importance to quality control from the very beginning to the end of the production.
Every product will be fully assembled and carefully tested before it's packed for shipment.